--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/usbdrv/usbdrvasm16.inc Thu Feb 16 14:40:23 2017 +0100
@@ -0,0 +1,345 @@
+/* Name: usbdrvasm16.inc
+ * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
+ * Author: Christian Starkjohann
+ * Creation Date: 2007-06-15
+ * Tabsize: 4
+ * Copyright: (c) 2007 by OBJECTIVE DEVELOPMENT Software GmbH
+ * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
+ */
+
+/* Do not link this file! Link usbdrvasm.S instead, which includes the
+ * appropriate implementation!
+ */
+
+/*
+General Description:
+This file is the 16 MHz version of the asssembler part of the USB driver. It
+requires a 16 MHz crystal (not a ceramic resonator and not a calibrated RC
+oscillator).
+
+See usbdrv.h for a description of the entire driver.
+
+Since almost all of this code is timing critical, don't change unless you
+really know what you are doing! Many parts require not only a maximum number
+of CPU cycles, but even an exact number of cycles!
+*/
+
+;max stack usage: [ret(2), YL, SREG, YH, bitcnt, shift, x1, x2, x3, x4, cnt] = 12 bytes
+;nominal frequency: 16 MHz -> 10.6666666 cycles per bit, 85.333333333 cycles per byte
+; Numbers in brackets are clocks counted from center of last sync bit
+; when instruction starts
+
+USB_INTR_VECTOR:
+;order of registers pushed: YL, SREG YH, [sofError], bitcnt, shift, x1, x2, x3, x4, cnt
+ push YL ;[-25] push only what is necessary to sync with edge ASAP
+ in YL, SREG ;[-23]
+ push YL ;[-22]
+ push YH ;[-20]
+;----------------------------------------------------------------------------
+; Synchronize with sync pattern:
+;----------------------------------------------------------------------------
+;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
+;sync up with J to K edge during sync pattern -- use fastest possible loops
+;The first part waits at most 1 bit long since we must be in sync pattern.
+;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
+;waitForJ, ensure that this prerequisite is met.
+waitForJ:
+ inc YL
+ sbis USBIN, USBMINUS
+ brne waitForJ ; just make sure we have ANY timeout
+waitForK:
+;The following code results in a sampling window of < 1/4 bit which meets the spec.
+ sbis USBIN, USBMINUS ;[-15]
+ rjmp foundK ;[-14]
+ sbis USBIN, USBMINUS
+ rjmp foundK
+ sbis USBIN, USBMINUS
+ rjmp foundK
+ sbis USBIN, USBMINUS
+ rjmp foundK
+ sbis USBIN, USBMINUS
+ rjmp foundK
+ sbis USBIN, USBMINUS
+ rjmp foundK
+#if USB_COUNT_SOF
+ lds YL, usbSofCount
+ inc YL
+ sts usbSofCount, YL
+#endif /* USB_COUNT_SOF */
+#ifdef USB_SOF_HOOK
+ USB_SOF_HOOK
+#endif
+ rjmp sofError
+foundK: ;[-12]
+;{3, 5} after falling D- edge, average delay: 4 cycles [we want 5 for center sampling]
+;we have 1 bit time for setup purposes, then sample again. Numbers in brackets
+;are cycles from center of first sync (double K) bit after the instruction
+ push bitcnt ;[-12]
+; [---] ;[-11]
+ lds YL, usbInputBufOffset;[-10]
+; [---] ;[-9]
+ clr YH ;[-8]
+ subi YL, lo8(-(usbRxBuf));[-7] [rx loop init]
+ sbci YH, hi8(-(usbRxBuf));[-6] [rx loop init]
+ push shift ;[-5]
+; [---] ;[-4]
+ ldi bitcnt, 0x55 ;[-3] [rx loop init]
+ sbis USBIN, USBMINUS ;[-2] we want two bits K (sample 2 cycles too early)
+ rjmp haveTwoBitsK ;[-1]
+ pop shift ;[0] undo the push from before
+ pop bitcnt ;[2] undo the push from before
+ rjmp waitForK ;[4] this was not the end of sync, retry
+; The entire loop from waitForK until rjmp waitForK above must not exceed two
+; bit times (= 21 cycles).
+
+;----------------------------------------------------------------------------
+; push more registers and initialize values while we sample the first bits:
+;----------------------------------------------------------------------------
+haveTwoBitsK:
+ push x1 ;[1]
+ push x2 ;[3]
+ push x3 ;[5]
+ ldi shift, 0 ;[7]
+ ldi x3, 1<<4 ;[8] [rx loop init] first sample is inverse bit, compensate that
+ push x4 ;[9] == leap
+
+ in x1, USBIN ;[11] <-- sample bit 0
+ andi x1, USBMASK ;[12]
+ bst x1, USBMINUS ;[13]
+ bld shift, 7 ;[14]
+ push cnt ;[15]
+ ldi leap, 0 ;[17] [rx loop init]
+ ldi cnt, USB_BUFSIZE;[18] [rx loop init]
+ rjmp rxbit1 ;[19] arrives at [21]
+
+;----------------------------------------------------------------------------
+; Receiver loop (numbers in brackets are cycles within byte after instr)
+;----------------------------------------------------------------------------
+
+; duration of unstuffing code should be 10.66666667 cycles. We adjust "leap"
+; accordingly to approximate this value in the long run.
+
+unstuff6:
+ andi x2, USBMASK ;[03]
+ ori x3, 1<<6 ;[04] will not be shifted any more
+ andi shift, ~0x80;[05]
+ mov x1, x2 ;[06] sampled bit 7 is actually re-sampled bit 6
+ subi leap, -1 ;[07] total duration = 11 bits -> subtract 1/3
+ rjmp didUnstuff6 ;[08]
+
+unstuff7:
+ ori x3, 1<<7 ;[09] will not be shifted any more
+ in x2, USBIN ;[00] [10] re-sample bit 7
+ andi x2, USBMASK ;[01]
+ andi shift, ~0x80;[02]
+ subi leap, 2 ;[03] total duration = 10 bits -> add 1/3
+ rjmp didUnstuff7 ;[04]
+
+unstuffEven:
+ ori x3, 1<<6 ;[09] will be shifted right 6 times for bit 0
+ in x1, USBIN ;[00] [10]
+ andi shift, ~0x80;[01]
+ andi x1, USBMASK ;[02]
+ breq se0 ;[03]
+ subi leap, -1 ;[04] total duration = 11 bits -> subtract 1/3
+ nop2 ;[05]
+ rjmp didUnstuffE ;[06]
+
+unstuffOdd:
+ ori x3, 1<<5 ;[09] will be shifted right 4 times for bit 1
+ in x2, USBIN ;[00] [10]
+ andi shift, ~0x80;[01]
+ andi x2, USBMASK ;[02]
+ breq se0 ;[03]
+ subi leap, -1 ;[04] total duration = 11 bits -> subtract 1/3
+ nop2 ;[05]
+ rjmp didUnstuffO ;[06]
+
+rxByteLoop:
+ andi x1, USBMASK ;[03]
+ eor x2, x1 ;[04]
+ subi leap, 1 ;[05]
+ brpl skipLeap ;[06]
+ subi leap, -3 ;1 one leap cycle every 3rd byte -> 85 + 1/3 cycles per byte
+ nop ;1
+skipLeap:
+ subi x2, 1 ;[08]
+ ror shift ;[09]
+didUnstuff6:
+ cpi shift, 0xfc ;[10]
+ in x2, USBIN ;[00] [11] <-- sample bit 7
+ brcc unstuff6 ;[01]
+ andi x2, USBMASK ;[02]
+ eor x1, x2 ;[03]
+ subi x1, 1 ;[04]
+ ror shift ;[05]
+didUnstuff7:
+ cpi shift, 0xfc ;[06]
+ brcc unstuff7 ;[07]
+ eor x3, shift ;[08] reconstruct: x3 is 1 at bit locations we changed, 0 at others
+ st y+, x3 ;[09] store data
+rxBitLoop:
+ in x1, USBIN ;[00] [11] <-- sample bit 0/2/4
+ andi x1, USBMASK ;[01]
+ eor x2, x1 ;[02]
+ andi x3, 0x3f ;[03] topmost two bits reserved for 6 and 7
+ subi x2, 1 ;[04]
+ ror shift ;[05]
+ cpi shift, 0xfc ;[06]
+ brcc unstuffEven ;[07]
+didUnstuffE:
+ lsr x3 ;[08]
+ lsr x3 ;[09]
+rxbit1:
+ in x2, USBIN ;[00] [10] <-- sample bit 1/3/5
+ andi x2, USBMASK ;[01]
+ breq se0 ;[02]
+ eor x1, x2 ;[03]
+ subi x1, 1 ;[04]
+ ror shift ;[05]
+ cpi shift, 0xfc ;[06]
+ brcc unstuffOdd ;[07]
+didUnstuffO:
+ subi bitcnt, 0xab;[08] == addi 0x55, 0x55 = 0x100/3
+ brcs rxBitLoop ;[09]
+
+ subi cnt, 1 ;[10]
+ in x1, USBIN ;[00] [11] <-- sample bit 6
+ brcc rxByteLoop ;[01]
+ rjmp overflow
+
+macro POP_STANDARD ; 14 cycles
+ pop cnt
+ pop x4
+ pop x3
+ pop x2
+ pop x1
+ pop shift
+ pop bitcnt
+ endm
+macro POP_RETI ; 7 cycles
+ pop YH
+ pop YL
+ out SREG, YL
+ pop YL
+ endm
+
+#include "asmcommon.inc"
+
+; USB spec says:
+; idle = J
+; J = (D+ = 0), (D- = 1)
+; K = (D+ = 1), (D- = 0)
+; Spec allows 7.5 bit times from EOP to SOP for replies
+
+bitstuffN:
+ eor x1, x4 ;[5]
+ ldi x2, 0 ;[6]
+ nop2 ;[7]
+ nop ;[9]
+ out USBOUT, x1 ;[10] <-- out
+ rjmp didStuffN ;[0]
+
+bitstuff6:
+ eor x1, x4 ;[5]
+ ldi x2, 0 ;[6] Carry is zero due to brcc
+ rol shift ;[7] compensate for ror shift at branch destination
+ rjmp didStuff6 ;[8]
+
+bitstuff7:
+ ldi x2, 0 ;[2] Carry is zero due to brcc
+ rjmp didStuff7 ;[3]
+
+
+sendNakAndReti:
+ ldi x3, USBPID_NAK ;[-18]
+ rjmp sendX3AndReti ;[-17]
+sendAckAndReti:
+ ldi cnt, USBPID_ACK ;[-17]
+sendCntAndReti:
+ mov x3, cnt ;[-16]
+sendX3AndReti:
+ ldi YL, 20 ;[-15] x3==r20 address is 20
+ ldi YH, 0 ;[-14]
+ ldi cnt, 2 ;[-13]
+; rjmp usbSendAndReti fallthrough
+
+;usbSend:
+;pointer to data in 'Y'
+;number of bytes in 'cnt' -- including sync byte [range 2 ... 12]
+;uses: x1...x4, btcnt, shift, cnt, Y
+;Numbers in brackets are time since first bit of sync pattern is sent
+;We don't match the transfer rate exactly (don't insert leap cycles every third
+;byte) because the spec demands only 1.5% precision anyway.
+usbSendAndReti: ; 12 cycles until SOP
+ in x2, USBDDR ;[-12]
+ ori x2, USBMASK ;[-11]
+ sbi USBOUT, USBMINUS;[-10] prepare idle state; D+ and D- must have been 0 (no pullups)
+ in x1, USBOUT ;[-8] port mirror for tx loop
+ out USBDDR, x2 ;[-7] <- acquire bus
+; need not init x2 (bitstuff history) because sync starts with 0
+ ldi x4, USBMASK ;[-6] exor mask
+ ldi shift, 0x80 ;[-5] sync byte is first byte sent
+txByteLoop:
+ ldi bitcnt, 0x35 ;[-4] [6] binary 0011 0101
+txBitLoop:
+ sbrs shift, 0 ;[-3] [7]
+ eor x1, x4 ;[-2] [8]
+ out USBOUT, x1 ;[-1] [9] <-- out N
+ ror shift ;[0] [10]
+ ror x2 ;[1]
+didStuffN:
+ cpi x2, 0xfc ;[2]
+ brcc bitstuffN ;[3]
+ lsr bitcnt ;[4]
+ brcc txBitLoop ;[5]
+ brne txBitLoop ;[6]
+
+ sbrs shift, 0 ;[7]
+ eor x1, x4 ;[8]
+didStuff6:
+ out USBOUT, x1 ;[-1] [9] <-- out 6
+ ror shift ;[0] [10]
+ ror x2 ;[1]
+ cpi x2, 0xfc ;[2]
+ brcc bitstuff6 ;[3]
+ ror shift ;[4]
+didStuff7:
+ ror x2 ;[5]
+ sbrs x2, 7 ;[6]
+ eor x1, x4 ;[7]
+ nop ;[8]
+ cpi x2, 0xfc ;[9]
+ out USBOUT, x1 ;[-1][10] <-- out 7
+ brcc bitstuff7 ;[0] [11]
+ ld shift, y+ ;[1]
+ dec cnt ;[3]
+ brne txByteLoop ;[4]
+;make SE0:
+ cbr x1, USBMASK ;[5] prepare SE0 [spec says EOP may be 21 to 25 cycles]
+ lds x2, usbNewDeviceAddr;[6]
+ lsl x2 ;[8] we compare with left shifted address
+ subi YL, 20 + 2 ;[9] Only assign address on data packets, not ACK/NAK in x3
+ sbci YH, 0 ;[10]
+ out USBOUT, x1 ;[11] <-- out SE0 -- from now 2 bits = 22 cycles until bus idle
+;2006-03-06: moved transfer of new address to usbDeviceAddr from C-Code to asm:
+;set address only after data packet was sent, not after handshake
+ breq skipAddrAssign ;[0]
+ sts usbDeviceAddr, x2; if not skipped: SE0 is one cycle longer
+skipAddrAssign:
+;end of usbDeviceAddress transfer
+ ldi x2, 1<<USB_INTR_PENDING_BIT;[2] int0 occurred during TX -- clear pending flag
+ USB_STORE_PENDING(x2) ;[3]
+ ori x1, USBIDLE ;[4]
+ in x2, USBDDR ;[5]
+ cbr x2, USBMASK ;[6] set both pins to input
+ mov x3, x1 ;[7]
+ cbr x3, USBMASK ;[8] configure no pullup on both pins
+ ldi x4, 4 ;[9]
+se0Delay:
+ dec x4 ;[10] [13] [16] [19]
+ brne se0Delay ;[11] [14] [17] [20]
+ out USBOUT, x1 ;[21] <-- out J (idle) -- end of SE0 (EOP signal)
+ out USBDDR, x2 ;[22] <-- release bus now
+ out USBOUT, x3 ;[23] <-- ensure no pull-up resistors are active
+ rjmp doReturn