usbdrv/usbconfig-prototype.h

changeset 0
9e9b2c78bd31
equal deleted inserted replaced
-1:000000000000 0:9e9b2c78bd31
1 /* Name: usbconfig.h
2 * Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
3 * Author: Christian Starkjohann
4 * Creation Date: 2005-04-01
5 * Tabsize: 4
6 * Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
7 * License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
8 */
9
10 #ifndef __usbconfig_h_included__
11 #define __usbconfig_h_included__
12
13 /*
14 General Description:
15 This file is an example configuration (with inline documentation) for the USB
16 driver. It configures V-USB for USB D+ connected to Port D bit 2 (which is
17 also hardware interrupt 0 on many devices) and USB D- to Port D bit 4. You may
18 wire the lines to any other port, as long as D+ is also wired to INT0 (or any
19 other hardware interrupt, as long as it is the highest level interrupt, see
20 section at the end of this file).
21 + To create your own usbconfig.h file, copy this file to your project's
22 + firmware source directory) and rename it to "usbconfig.h".
23 + Then edit it accordingly.
24 */
25
26 /* ---------------------------- Hardware Config ---------------------------- */
27
28 #define USB_CFG_IOPORTNAME D
29 /* This is the port where the USB bus is connected. When you configure it to
30 * "B", the registers PORTB, PINB and DDRB will be used.
31 */
32 #define USB_CFG_DMINUS_BIT 4
33 /* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
34 * This may be any bit in the port.
35 */
36 #define USB_CFG_DPLUS_BIT 2
37 /* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
38 * This may be any bit in the port. Please note that D+ must also be connected
39 * to interrupt pin INT0! [You can also use other interrupts, see section
40 * "Optional MCU Description" below, or you can connect D- to the interrupt, as
41 * it is required if you use the USB_COUNT_SOF feature. If you use D- for the
42 * interrupt, the USB interrupt will also be triggered at Start-Of-Frame
43 * markers every millisecond.]
44 */
45 #define USB_CFG_CLOCK_KHZ (F_CPU/1000)
46 /* Clock rate of the AVR in kHz. Legal values are 12000, 12800, 15000, 16000,
47 * 16500, 18000 and 20000. The 12.8 MHz and 16.5 MHz versions of the code
48 * require no crystal, they tolerate +/- 1% deviation from the nominal
49 * frequency. All other rates require a precision of 2000 ppm and thus a
50 * crystal!
51 * Since F_CPU should be defined to your actual clock rate anyway, you should
52 * not need to modify this setting.
53 */
54 #define USB_CFG_CHECK_CRC 0
55 /* Define this to 1 if you want that the driver checks integrity of incoming
56 * data packets (CRC checks). CRC checks cost quite a bit of code size and are
57 * currently only available for 18 MHz crystal clock. You must choose
58 * USB_CFG_CLOCK_KHZ = 18000 if you enable this option.
59 */
60
61 /* ----------------------- Optional Hardware Config ------------------------ */
62
63 /* #define USB_CFG_PULLUP_IOPORTNAME D */
64 /* If you connect the 1.5k pullup resistor from D- to a port pin instead of
65 * V+, you can connect and disconnect the device from firmware by calling
66 * the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
67 * This constant defines the port on which the pullup resistor is connected.
68 */
69 /* #define USB_CFG_PULLUP_BIT 4 */
70 /* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
71 * above) where the 1.5k pullup resistor is connected. See description
72 * above for details.
73 */
74
75 /* --------------------------- Functional Range ---------------------------- */
76
77 #define USB_CFG_HAVE_INTRIN_ENDPOINT 0
78 /* Define this to 1 if you want to compile a version with two endpoints: The
79 * default control endpoint 0 and an interrupt-in endpoint (any other endpoint
80 * number).
81 */
82 #define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
83 /* Define this to 1 if you want to compile a version with three endpoints: The
84 * default control endpoint 0, an interrupt-in endpoint 3 (or the number
85 * configured below) and a catch-all default interrupt-in endpoint as above.
86 * You must also define USB_CFG_HAVE_INTRIN_ENDPOINT to 1 for this feature.
87 */
88 #define USB_CFG_EP3_NUMBER 3
89 /* If the so-called endpoint 3 is used, it can now be configured to any other
90 * endpoint number (except 0) with this macro. Default if undefined is 3.
91 */
92 /* #define USB_INITIAL_DATATOKEN USBPID_DATA1 */
93 /* The above macro defines the startup condition for data toggling on the
94 * interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA1.
95 * Since the token is toggled BEFORE sending any data, the first packet is
96 * sent with the oposite value of this configuration!
97 */
98 #define USB_CFG_IMPLEMENT_HALT 0
99 /* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
100 * for endpoint 1 (interrupt endpoint). Although you may not need this feature,
101 * it is required by the standard. We have made it a config option because it
102 * bloats the code considerably.
103 */
104 #define USB_CFG_SUPPRESS_INTR_CODE 0
105 /* Define this to 1 if you want to declare interrupt-in endpoints, but don't
106 * want to send any data over them. If this macro is defined to 1, functions
107 * usbSetInterrupt() and usbSetInterrupt3() are omitted. This is useful if
108 * you need the interrupt-in endpoints in order to comply to an interface
109 * (e.g. HID), but never want to send any data. This option saves a couple
110 * of bytes in flash memory and the transmit buffers in RAM.
111 */
112 #define USB_CFG_INTR_POLL_INTERVAL 10
113 /* If you compile a version with endpoint 1 (interrupt-in), this is the poll
114 * interval. The value is in milliseconds and must not be less than 10 ms for
115 * low speed devices.
116 */
117 #define USB_CFG_IS_SELF_POWERED 0
118 /* Define this to 1 if the device has its own power supply. Set it to 0 if the
119 * device is powered from the USB bus.
120 */
121 #define USB_CFG_MAX_BUS_POWER 100
122 /* Set this variable to the maximum USB bus power consumption of your device.
123 * The value is in milliamperes. [It will be divided by two since USB
124 * communicates power requirements in units of 2 mA.]
125 */
126 #define USB_CFG_IMPLEMENT_FN_WRITE 0
127 /* Set this to 1 if you want usbFunctionWrite() to be called for control-out
128 * transfers. Set it to 0 if you don't need it and want to save a couple of
129 * bytes.
130 */
131 #define USB_CFG_IMPLEMENT_FN_READ 0
132 /* Set this to 1 if you need to send control replies which are generated
133 * "on the fly" when usbFunctionRead() is called. If you only want to send
134 * data from a static buffer, set it to 0 and return the data from
135 * usbFunctionSetup(). This saves a couple of bytes.
136 */
137 #define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
138 /* Define this to 1 if you want to use interrupt-out (or bulk out) endpoints.
139 * You must implement the function usbFunctionWriteOut() which receives all
140 * interrupt/bulk data sent to any endpoint other than 0. The endpoint number
141 * can be found in 'usbRxToken'.
142 */
143 #define USB_CFG_HAVE_FLOWCONTROL 0
144 /* Define this to 1 if you want flowcontrol over USB data. See the definition
145 * of the macros usbDisableAllRequests() and usbEnableAllRequests() in
146 * usbdrv.h.
147 */
148 #define USB_CFG_DRIVER_FLASH_PAGE 0
149 /* If the device has more than 64 kBytes of flash, define this to the 64 k page
150 * where the driver's constants (descriptors) are located. Or in other words:
151 * Define this to 1 for boot loaders on the ATMega128.
152 */
153 #define USB_CFG_LONG_TRANSFERS 0
154 /* Define this to 1 if you want to send/receive blocks of more than 254 bytes
155 * in a single control-in or control-out transfer. Note that the capability
156 * for long transfers increases the driver size.
157 */
158 /* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
159 /* This macro is a hook if you want to do unconventional things. If it is
160 * defined, it's inserted at the beginning of received message processing.
161 * If you eat the received message and don't want default processing to
162 * proceed, do a return after doing your things. One possible application
163 * (besides debugging) is to flash a status LED on each packet.
164 */
165 /* #define USB_RESET_HOOK(resetStarts) if(!resetStarts){hadUsbReset();} */
166 /* This macro is a hook if you need to know when an USB RESET occurs. It has
167 * one parameter which distinguishes between the start of RESET state and its
168 * end.
169 */
170 /* #define USB_SET_ADDRESS_HOOK() hadAddressAssigned(); */
171 /* This macro (if defined) is executed when a USB SET_ADDRESS request was
172 * received.
173 */
174 #define USB_COUNT_SOF 0
175 /* define this macro to 1 if you need the global variable "usbSofCount" which
176 * counts SOF packets. This feature requires that the hardware interrupt is
177 * connected to D- instead of D+.
178 */
179 /* #ifdef __ASSEMBLER__
180 * macro myAssemblerMacro
181 * in YL, TCNT0
182 * sts timer0Snapshot, YL
183 * endm
184 * #endif
185 * #define USB_SOF_HOOK myAssemblerMacro
186 * This macro (if defined) is executed in the assembler module when a
187 * Start Of Frame condition is detected. It is recommended to define it to
188 * the name of an assembler macro which is defined here as well so that more
189 * than one assembler instruction can be used. The macro may use the register
190 * YL and modify SREG. If it lasts longer than a couple of cycles, USB messages
191 * immediately after an SOF pulse may be lost and must be retried by the host.
192 * What can you do with this hook? Since the SOF signal occurs exactly every
193 * 1 ms (unless the host is in sleep mode), you can use it to tune OSCCAL in
194 * designs running on the internal RC oscillator.
195 * Please note that Start Of Frame detection works only if D- is wired to the
196 * interrupt, not D+. THIS IS DIFFERENT THAN MOST EXAMPLES!
197 */
198 #define USB_CFG_CHECK_DATA_TOGGLING 0
199 /* define this macro to 1 if you want to filter out duplicate data packets
200 * sent by the host. Duplicates occur only as a consequence of communication
201 * errors, when the host does not receive an ACK. Please note that you need to
202 * implement the filtering yourself in usbFunctionWriteOut() and
203 * usbFunctionWrite(). Use the global usbCurrentDataToken and a static variable
204 * for each control- and out-endpoint to check for duplicate packets.
205 */
206 #define USB_CFG_HAVE_MEASURE_FRAME_LENGTH 0
207 /* define this macro to 1 if you want the function usbMeasureFrameLength()
208 * compiled in. This function can be used to calibrate the AVR's RC oscillator.
209 */
210 #define USB_USE_FAST_CRC 0
211 /* The assembler module has two implementations for the CRC algorithm. One is
212 * faster, the other is smaller. This CRC routine is only used for transmitted
213 * messages where timing is not critical. The faster routine needs 31 cycles
214 * per byte while the smaller one needs 61 to 69 cycles. The faster routine
215 * may be worth the 32 bytes bigger code size if you transmit lots of data and
216 * run the AVR close to its limit.
217 */
218
219 /* -------------------------- Device Description --------------------------- */
220
221 #define USB_CFG_VENDOR_ID 0xc0, 0x16 /* = 0x16c0 = 5824 = voti.nl */
222 /* USB vendor ID for the device, low byte first. If you have registered your
223 * own Vendor ID, define it here. Otherwise you may use one of obdev's free
224 * shared VID/PID pairs. Be sure to read USB-IDs-for-free.txt for rules!
225 * *** IMPORTANT NOTE ***
226 * This template uses obdev's shared VID/PID pair for Vendor Class devices
227 * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
228 * the implications!
229 */
230 #define USB_CFG_DEVICE_ID 0xdc, 0x05 /* = 0x05dc = 1500 */
231 /* This is the ID of the product, low byte first. It is interpreted in the
232 * scope of the vendor ID. If you have registered your own VID with usb.org
233 * or if you have licensed a PID from somebody else, define it here. Otherwise
234 * you may use one of obdev's free shared VID/PID pairs. See the file
235 * USB-IDs-for-free.txt for details!
236 * *** IMPORTANT NOTE ***
237 * This template uses obdev's shared VID/PID pair for Vendor Class devices
238 * with libusb: 0x16c0/0x5dc. Use this VID/PID pair ONLY if you understand
239 * the implications!
240 */
241 #define USB_CFG_DEVICE_VERSION 0x00, 0x01
242 /* Version number of the device: Minor number first, then major number.
243 */
244 #define USB_CFG_VENDOR_NAME 'o', 'b', 'd', 'e', 'v', '.', 'a', 't'
245 #define USB_CFG_VENDOR_NAME_LEN 8
246 /* These two values define the vendor name returned by the USB device. The name
247 * must be given as a list of characters under single quotes. The characters
248 * are interpreted as Unicode (UTF-16) entities.
249 * If you don't want a vendor name string, undefine these macros.
250 * ALWAYS define a vendor name containing your Internet domain name if you use
251 * obdev's free shared VID/PID pair. See the file USB-IDs-for-free.txt for
252 * details.
253 */
254 #define USB_CFG_DEVICE_NAME 'T', 'e', 'm', 'p', 'l', 'a', 't', 'e'
255 #define USB_CFG_DEVICE_NAME_LEN 8
256 /* Same as above for the device name. If you don't want a device name, undefine
257 * the macros. See the file USB-IDs-for-free.txt before you assign a name if
258 * you use a shared VID/PID.
259 */
260 /*#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e' */
261 /*#define USB_CFG_SERIAL_NUMBER_LEN 0 */
262 /* Same as above for the serial number. If you don't want a serial number,
263 * undefine the macros.
264 * It may be useful to provide the serial number through other means than at
265 * compile time. See the section about descriptor properties below for how
266 * to fine tune control over USB descriptors such as the string descriptor
267 * for the serial number.
268 */
269 #define USB_CFG_DEVICE_CLASS 0xff /* set to 0 if deferred to interface */
270 #define USB_CFG_DEVICE_SUBCLASS 0
271 /* See USB specification if you want to conform to an existing device class.
272 * Class 0xff is "vendor specific".
273 */
274 #define USB_CFG_INTERFACE_CLASS 0 /* define class here if not at device level */
275 #define USB_CFG_INTERFACE_SUBCLASS 0
276 #define USB_CFG_INTERFACE_PROTOCOL 0
277 /* See USB specification if you want to conform to an existing device class or
278 * protocol. The following classes must be set at interface level:
279 * HID class is 3, no subclass and protocol required (but may be useful!)
280 * CDC class is 2, use subclass 2 and protocol 1 for ACM
281 */
282 /* #define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 42 */
283 /* Define this to the length of the HID report descriptor, if you implement
284 * an HID device. Otherwise don't define it or define it to 0.
285 * If you use this define, you must add a PROGMEM character array named
286 * "usbHidReportDescriptor" to your code which contains the report descriptor.
287 * Don't forget to keep the array and this define in sync!
288 */
289
290 /* #define USB_PUBLIC static */
291 /* Use the define above if you #include usbdrv.c instead of linking against it.
292 * This technique saves a couple of bytes in flash memory.
293 */
294
295 /* ------------------- Fine Control over USB Descriptors ------------------- */
296 /* If you don't want to use the driver's default USB descriptors, you can
297 * provide our own. These can be provided as (1) fixed length static data in
298 * flash memory, (2) fixed length static data in RAM or (3) dynamically at
299 * runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
300 * information about this function.
301 * Descriptor handling is configured through the descriptor's properties. If
302 * no properties are defined or if they are 0, the default descriptor is used.
303 * Possible properties are:
304 * + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
305 * at runtime via usbFunctionDescriptor(). If the usbMsgPtr mechanism is
306 * used, the data is in FLASH by default. Add property USB_PROP_IS_RAM if
307 * you want RAM pointers.
308 * + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
309 * in static memory is in RAM, not in flash memory.
310 * + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
311 * the driver must know the descriptor's length. The descriptor itself is
312 * found at the address of a well known identifier (see below).
313 * List of static descriptor names (must be declared PROGMEM if in flash):
314 * char usbDescriptorDevice[];
315 * char usbDescriptorConfiguration[];
316 * char usbDescriptorHidReport[];
317 * char usbDescriptorString0[];
318 * int usbDescriptorStringVendor[];
319 * int usbDescriptorStringDevice[];
320 * int usbDescriptorStringSerialNumber[];
321 * Other descriptors can't be provided statically, they must be provided
322 * dynamically at runtime.
323 *
324 * Descriptor properties are or-ed or added together, e.g.:
325 * #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
326 *
327 * The following descriptors are defined:
328 * USB_CFG_DESCR_PROPS_DEVICE
329 * USB_CFG_DESCR_PROPS_CONFIGURATION
330 * USB_CFG_DESCR_PROPS_STRINGS
331 * USB_CFG_DESCR_PROPS_STRING_0
332 * USB_CFG_DESCR_PROPS_STRING_VENDOR
333 * USB_CFG_DESCR_PROPS_STRING_PRODUCT
334 * USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
335 * USB_CFG_DESCR_PROPS_HID
336 * USB_CFG_DESCR_PROPS_HID_REPORT
337 * USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
338 *
339 * Note about string descriptors: String descriptors are not just strings, they
340 * are Unicode strings prefixed with a 2 byte header. Example:
341 * int serialNumberDescriptor[] = {
342 * USB_STRING_DESCRIPTOR_HEADER(6),
343 * 'S', 'e', 'r', 'i', 'a', 'l'
344 * };
345 */
346
347 #define USB_CFG_DESCR_PROPS_DEVICE 0
348 #define USB_CFG_DESCR_PROPS_CONFIGURATION 0
349 #define USB_CFG_DESCR_PROPS_STRINGS 0
350 #define USB_CFG_DESCR_PROPS_STRING_0 0
351 #define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
352 #define USB_CFG_DESCR_PROPS_STRING_PRODUCT 0
353 #define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER 0
354 #define USB_CFG_DESCR_PROPS_HID 0
355 #define USB_CFG_DESCR_PROPS_HID_REPORT 0
356 #define USB_CFG_DESCR_PROPS_UNKNOWN 0
357
358
359 #define usbMsgPtr_t unsigned short
360 /* If usbMsgPtr_t is not defined, it defaults to 'uchar *'. We define it to
361 * a scalar type here because gcc generates slightly shorter code for scalar
362 * arithmetics than for pointer arithmetics. Remove this define for backward
363 * type compatibility or define it to an 8 bit type if you use data in RAM only
364 * and all RAM is below 256 bytes (tiny memory model in IAR CC).
365 */
366
367 /* ----------------------- Optional MCU Description ------------------------ */
368
369 /* The following configurations have working defaults in usbdrv.h. You
370 * usually don't need to set them explicitly. Only if you want to run
371 * the driver on a device which is not yet supported or with a compiler
372 * which is not fully supported (such as IAR C) or if you use a differnt
373 * interrupt than INT0, you may have to define some of these.
374 */
375 /* #define USB_INTR_CFG MCUCR */
376 /* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
377 /* #define USB_INTR_CFG_CLR 0 */
378 /* #define USB_INTR_ENABLE GIMSK */
379 /* #define USB_INTR_ENABLE_BIT INT0 */
380 /* #define USB_INTR_PENDING GIFR */
381 /* #define USB_INTR_PENDING_BIT INTF0 */
382 /* #define USB_INTR_VECTOR INT0_vect */
383
384 #endif /* __usbconfig_h_included__ */

mercurial