--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/SdFatConfig.h Sat Nov 07 13:23:07 2015 +0100
@@ -0,0 +1,114 @@
+/* Arduino SdFat Library
+ * Copyright (C) 2009 by William Greiman
+ *
+ * This file is part of the Arduino SdFat Library
+ *
+ * This Library is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This Library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with the Arduino SdFat Library. If not, see
+ * <http://www.gnu.org/licenses/>.
+ */
+/**
+ * \file
+ * \brief configuration definitions
+ */
+#include "Marlin.h"
+#ifdef SDSUPPORT
+
+#ifndef SdFatConfig_h
+#define SdFatConfig_h
+#include <stdint.h>
+//------------------------------------------------------------------------------
+/**
+ * To use multiple SD cards set USE_MULTIPLE_CARDS nonzero.
+ *
+ * Using multiple cards costs 400 - 500 bytes of flash.
+ *
+ * Each card requires about 550 bytes of SRAM so use of a Mega is recommended.
+ */
+#define USE_MULTIPLE_CARDS 0
+//------------------------------------------------------------------------------
+/**
+ * Call flush for endl if ENDL_CALLS_FLUSH is nonzero
+ *
+ * The standard for iostreams is to call flush. This is very costly for
+ * SdFat. Each call to flush causes 2048 bytes of I/O to the SD.
+ *
+ * SdFat has a single 512 byte buffer for SD I/O so it must write the current
+ * data block to the SD, read the directory block from the SD, update the
+ * directory entry, write the directory block to the SD and read the data
+ * block back into the buffer.
+ *
+ * The SD flash memory controller is not designed for this many rewrites
+ * so performance may be reduced by more than a factor of 100.
+ *
+ * If ENDL_CALLS_FLUSH is zero, you must call flush and/or close to force
+ * all data to be written to the SD.
+ */
+#define ENDL_CALLS_FLUSH 0
+//------------------------------------------------------------------------------
+/**
+ * Allow use of deprecated functions if ALLOW_DEPRECATED_FUNCTIONS is nonzero
+ */
+#define ALLOW_DEPRECATED_FUNCTIONS 1
+//------------------------------------------------------------------------------
+/**
+ * Allow FAT12 volumes if FAT12_SUPPORT is nonzero.
+ * FAT12 has not been well tested.
+ */
+#define FAT12_SUPPORT 0
+//------------------------------------------------------------------------------
+/**
+ * SPI init rate for SD initialization commands. Must be 5 (F_CPU/64)
+ * or 6 (F_CPU/128).
+ */
+#define SPI_SD_INIT_RATE 5
+//------------------------------------------------------------------------------
+/**
+ * Set the SS pin high for hardware SPI. If SS is chip select for another SPI
+ * device this will disable that device during the SD init phase.
+ */
+#define SET_SPI_SS_HIGH 1
+//------------------------------------------------------------------------------
+/**
+ * Define MEGA_SOFT_SPI nonzero to use software SPI on Mega Arduinos.
+ * Pins used are SS 10, MOSI 11, MISO 12, and SCK 13.
+ *
+ * MEGA_SOFT_SPI allows an unmodified Adafruit GPS Shield to be used
+ * on Mega Arduinos. Software SPI works well with GPS Shield V1.1
+ * but many SD cards will fail with GPS Shield V1.0.
+ */
+#define MEGA_SOFT_SPI 0
+//------------------------------------------------------------------------------
+/**
+ * Set USE_SOFTWARE_SPI nonzero to always use software SPI.
+ */
+#define USE_SOFTWARE_SPI 0
+// define software SPI pins so Mega can use unmodified 168/328 shields
+/** Software SPI chip select pin for the SD */
+uint8_t const SOFT_SPI_CS_PIN = 10;
+/** Software SPI Master Out Slave In pin */
+uint8_t const SOFT_SPI_MOSI_PIN = 11;
+/** Software SPI Master In Slave Out pin */
+uint8_t const SOFT_SPI_MISO_PIN = 12;
+/** Software SPI Clock pin */
+uint8_t const SOFT_SPI_SCK_PIN = 13;
+//------------------------------------------------------------------------------
+/**
+ * The __cxa_pure_virtual function is an error handler that is invoked when
+ * a pure virtual function is called.
+ */
+#define USE_CXA_PURE_VIRTUAL 1
+#endif // SdFatConfig_h
+
+
+#endif
\ No newline at end of file
